H9 SI17 Glossy Panel & Paint 50ml/1.7oz

This Thin Film Coatings can be applied easily with a simple ‘clean and wipe’ method they not only restore the surface’s original luster but also offer enhanced UV protection, boasting an impressive 9H hardness to resist micro-scratches. NANO-CERAMIC® Thin Film Coatings significantly extend the lifetime of panels or painted surfaces by an additional 15-25 years or more, owing to their user-friendly application and reapplication for continuous protection.

Moreover, these coatings demonstrate temperature resistance up to 850°C/1600°F, effectively repelling water, dirt, dust, and contaminants, thereby reducing cleaning and maintenance expenses. This level of protection not only preserves aesthetic appeal but also enhances customer attraction, ensuring a secure investment. It is important to note that our thin coating can only be applied if the existing surface coating is in good condition (not brittle). Waiting for this moment may result in costly repainting.face coating is still in good condition (non-brittle). Waiting until this point could result in costly repaints.

• Thickness: 6 micron 

• Hydrophobic

• Hardness H9

• Durability : Near Permanent

• Temperature resistance: 850C

Advantages

• Increased surface hardness

• Renews marble and granite

• Makes the surface hard and smooth, permanently protected 

• Creates an easy-to-clean surface

• Repels water and dirt.

• Scratch resistant, optimal protection from the clear layer underneath

• UV Protection 

• Cost reduction, cleaning intervals will be extended

Recommendations

• A fully cured SI17 layer can only be removed by machine polishing from the surface, using wool pad and heavy compound.

• Prior to the application of a SI17 Ceramic layer it is crucial that the surface is in a new or like-new condition.

• We recommend to clean the surface prior to the application with our sterile cleaner

Easy to Apply

Application; 1. Clean the surface 2. Sterilize the surface  3. Apply via the cotton pad an even layer  4. Let it cure.

APPLICATION VIDEO SI17

Spray application

Process: HVLP-compressed air, Spray gun: e.g. SATA minijet HVLP , Working pressure: ca. 2 – 3 bar

Nozzles: 0.8 – 1.3 mm 0.03-0.05”

Curing:

Ambient Curing:

• The ideal temperature range is typically between 20°C / 70°F and 35°C / 95°F.

Humidity:

• The relative humidity should be below 70%.

Curing Time:

• Complete curing time is approximately 5 days; after this period, the curing can be checked.

Heat Curing:

• Cure at 120°C / 250°F  for 1.5 hours.

• Verify that the coating is completely cured after heating in the oven.

• To check curing, press your finger firmly on the coated surface. No material should stick to your finger.

Curing by Hot Air Blow:

• Set the hot air gun temperature to 120°C / 250°F  to 130°C / 265°F and apply for 3 to 4 minutes.

• Approximately 80% to 90% curing can occur within 3 to 4 minutes. After this, the surface will be dry. Full curing requires 24 hours.

• Stacking should be avoided until full curing is achieved.

.

Storage and handling

Store in dark and dry conditions at room temperature.

Use gloves and mask.

Ask for our MSDS via 24h - Emergency Phone: +62 811 640 5000 (advisory service in German, English, or Bahasa language)

Content of packaging

• 1 Pcs 50ml/1.7oz SI17 Coating  (Suitable for Glossy ACP Panels and Glossy Painted Surfaces)

• 1 Micro towel 40x40cm 15"x15"

• 6 Cotton pad

• 1 Dripper plug

• 1 Pair Nitrile Gloves

Packaging Information

Includes plastic sealed wrap

1 pcs Weight 180 gram/ 0.4 lbs single carton size L9.5cm x W6cm x H11cm / L3.7inch x W2.4inch x H4.3inch

82 pcs in carton W52cm x H25cm x D44cm / W22inch x H15inch x D18inch Weight 14,8 kg 32,6 lbs